Keyless2Go Keyless Entry Remote Head Key Fob for select Toyota Rav4 Highlander Tacoma GQ4-52T w/ Trunk Release

This key worked fine. I have no complaints, the fob programmed to the vehicle and the correct chip was inside of the key. I had a terrible experience with a different seller, but this definitely made things right

Perfect fit, easy to program and works perfectly! Much cheaper than the dealership!

Got this for a 2017 Toyota Highlander. I checked my master key and it has an H on it, so I bought this one. I was able to program is very quickly with one of the OBD port program devices (you can find on Amazon)I tried many youtube videos of putting the key in the ignition and taking it out, opening/closing the door. None of that worked. Maybe because I have a 2017. The OBD device programmed the key and fob in under 2 mins (it did take me a couple of times, only because I messed up the steps) I just ordered 2 more keys to have on hand.Once I had them programmed, I then got them cut at a a local (national) hardware store (sounds like mace) :-) You do NOT need any code from the dealer or have to get them cut at the dealership. In fact, because I brought the key in, he didn't charge me to cut it (I was expecting to pay $5-$10) I think at the local dealer the key, programming and cutting would cost me $125 (or more)? (ODB programmer and Key was just over $80)The place where you get it cut "Might" need to have programmed in their machine the same blank. They should have it. They have to be able to tell the machine that the blank you give them and they are putting in their machine is "such and such" a blank. When I had my cut, he found the blank they sell and it matched. So it was no problem cutting it. Started the car right up.I am a very pessimistic guy and don't give good reviews unless it's warranted. But I saved myself about $45 and it took an hour of mine time (reading the OBD device instructions, looking at youtube, trying a couple times, getting the key cut).

They key turns the car on but the buttons aren’t compatible with car even though it’ states it was

My wife's Highlander need a new key (she ran over the old one with the lawn mower) Ugh!! There are 3 steps to using this key.1. Program the remote- watch YouTube video2. Program the security chip- watch YouTube video3. get the Key cut (Ace hardware wouldn't do it because they said you had to buy the key from them for it) Make sure you find someone to do it. a locksmith will do it but it may cost more. We found an old guy in a leather shop with a key cutting machine and an old dog to keep us company.You can to them in any order. in the end it cost less than 25% of what a dealership would have wanted.

I ordered two key fobs and my locksmith was going to program them. The keys arrived on time but there was just one problem. The battery was already dead in the key fob. The battery had to be replaced before the locksmith could program the key. When I later called the company that I bought them from, their basic attitude was too bad, we don't care. They did offer to send me replacement batteries that had already been replaced by the locksmith but not reimburse me. Their whole attitude was "tough luck, we can't check the batteries, your problem."This time I was lucky I wasn't on the side of the road because I couldn't start my car because of a dead fob battery.My suggestion, find another company that is customer service-oriented, not a company like Keyless2Go, that appeared to care less if they sent out a defective product that was not working.

I bought this key to save money over going to the dealer. I called several locksmiths. All of them wanted $120 and up to cut and program the key. the told me that they have tired these keys in the past and that it may not program properly and then the key is no good. They said I would still have to pay them the $120.

The key works perfectly for my Canadian built 2016 Rav4 XLE! I had a store cut it and I programmed the key and remote myself with the Autel AP200 (btw, i highly recommend for fifty dollars) Saved me hundreds!! Couldn’t be more pleased with this product.Just make sure your FCC ID (GQ4-52T) is the same as this replacement by opening the case of your original key. You’ll see the ID number printed on the remote once you open the case. Also make sure there is a “H” printed on the shank of your original key. If all of this matches, this remote should work for you, no problem!