QWORK Hard Storage Tools Case Replacement, for Store Electric drill and Tool Sharpeners, 33x22.5x9cm, Case Only

Got this case to carry my RYOBI P737D power inflator behind the seat of my P/U truck for emergencies.As can been seen by the attached picture, it fits comfortably with wiggle room on all sides with a current production 4Ah battery attached. The hose coming out the left side may "look like" it's a hard left turn, but trust me, it's not, just the camera playing tricks on your eyes.Overall, it seems to be well made, both zippers move freely. I've only had it for a few days, only time will tell about long term durability.Was looking at the "Tourmate Hard Storage Case for RYOBI P737": I measured my P737D with a 4Ah battery attached & compared my measurements to the provided dimensions - it should fit | but listing pictures show otherwise.Also looked at the "khanka Hard Travel Case for Ryobi P737" - the listing pictures show the tool fitting well with a 4Ah battery attached. Now read the reviews, people who have purchased & used it say otherwise.In my original review I stated.. FYI: Ryobi P215 1/2" drill/driver also fits with 4Ah battery installed...UPDATE: Now that Amazon has posted my review I’m adding a pic of the RYOBI P215 1/2" drill/driver sitting in the QWORK case with two 4Ah batteries. Great way for trades people to carry this tool to a job site with an extra 4Ah battery charged up & ready to go.As stated in my original review, you have to turn the chuck until the jaws are flush with / inside of it for a good fit. There’s plenty of room to carry the tool with a single 6Ah high performance battery attached or not attached with room left over for various nik-naks like.. drill/torx/phillips bits etc.The QWORK case sells for under $16 for one & less than $20 for two (I purchased the two pak) | Tourmate is over $16 for one | Khanka is $26.99 for one & the tool doesn't fit correctly according to those have purchased & used it.Note: I also updated the model number of my RYOBI inflator because RYOBI's website REQUIRES precise model numbers to be entered in the search box or you'll get a "No Results Found" error message(SMH).Value: the QWORK case costs less & the tools fit better than other options -- you be the judge.

It fit my 20V drill, battery, charger, and miscellaneous accessories perfectly, including a case of DeWalt drill bits that's almost as big as the drill itself. It's a hard case, but has a streamlined exterior. Because it's not hard plastic, you can wedge it in between something else. When you're carrying a bunch of stuff for a project, the soft handle means you can hang it off a couple of fingers without it digging into them. It was exactly what I was looking for. My bigger power tools all came with their own bags so I don't know how this would fit anything much bigger. I also wouldn't recommend it for smaller hand tools like screwdrivers or wrenches because there aren't any straps to keep smaller things in place. (Unless you don't mind them jumbled together). I'm going to buy another of these for my pneumatic brad gun and I'm also thinking of buying one for my socket wrenches because I can take the plastic insert out and put it inside one of these so that I have a case with a handle to carry them.

lootI recently purchased a Dremel 3100 and given the fact that Dremel does not make a carrying case for this particular model I needed something besides the cardboard box that it is packaged in. After looking around on Amazon and other places I settled on this case. It fits the size of the tool very well and it's very adequate for storing and transporting the device from place to place also there was enough room inside the case to store quite a few bits and attachments. My only complaint on the case is that the inside mesh pocket is a bit too stretchy but not resilient in other words it will expand quite a bit but doesn't spring back into place quite as well as it ought to. Considering the cost of the case and all the pluses as opposed that one small problem I think it is a great value for the money. I would rate it five stars instead of four except for the non-resilance of the inside mesh pocket. I would definitely recommend the case but just know that the inside mesh pocket does not have great resilient strength to pop back into place so if you're looking to store your bits and accessories there it's not going to work very well for that. The case overall is quite good though!

Perfect no problems

Awesome! It fits my bosch 12v drill and driver perfectly. Along with a bunch of drill bits. Great price and seems durable.

Works very well for what I’m using it for, store steam mop pads and accessories.

These are not hard cases as advertised. They're very nicely made and probably have a good purpose for something but they certainly aren't strong enough to be able to store a drill. They probably could be used maybe to the store some light electronics but certainly nothing too heavy.

I couldn't be more pleased with this case. I purchased it specifically to use, and replace the Carrying Case for my Dremel tool. Because like EVERY OTHER Tool on the market, the carrying case is ALWAYS TOO SMALL, especially for 'power cord' stowage. THIS CASE Is Great. Plenty of room with room to spare. In reality, I have purchased several of the same size for Multimeters and Scanners.These cases are definitely worth every penny!